WSAAsyncGetServByPort  0BJQDW

The Windows Sockets WSAAsyncGetServByPort function gets service information corresponding to a port and protocolasynchronous version.

HANDLE WSAAsyncGetServByPort (

Parameters

hWnd

[in] The handle of the window which should receive a message when the asynchronous request completes.

wMsg

[in] The message to be received when the asynchronous request completes.

port

[in] The port for the service, in network byte order.

proto

[in] A pointer to a protocol name. This can be NULL, in which case WSAAsyncGetServByPort will search for the first service entry for which s_port match the given port. Otherwise, WSAAsyncGetServByPort matches both port and proto.

buf

[out] A pointer to the data area to receive the servent data. Note that this must be larger than the size of a servent structure. This is because the data area supplied is used by Windows Sockets to contain not only a servent structure but any and all of the data which is referenced by members of the servent structure. It is recommended that you supply a buffer of MAXGETHOSTSTRUCT bytes.

buflen

[in] The size of data area buf above.

Remarks

This function is an asynchronous version of getservbyport, and is used to retrieve service information corresponding to a port number. Windows Sockets initiates the operation and returns to the caller immediately, passing back an opaque "asynchronous task handle" which the application can use to identify the operation. When the operation is completed, the results (if any) are copied into the buffer provided by the caller and a message is sent to the application's window.

When the asynchronous operation is complete the application's window hWnd receives message wMsg. The wParam argument contains the asynchronous task handle as returned by the original function call. The high 16 bits of lParam contain any error code. The error code can be any error as defined in WINSOCK2.H. An error code of zero indicates successful completion of the asynchronous operation. On successful completion, the buffer supplied to the original function call contains a servent structure. To access the elements of this structure, the original buffer address should be cast to a servent structure pointer and accessed as appropriate.

Note that if the error code is WSAENOBUFS, it indicates that the size of the buffer specified by buflen in the original call was too small to contain all the resultant information. In this case, the low 16 bits of lParam contain the size of buffer required to supply ALL the requisite information. If the application decides that the partial data is inadequate, it can reissue the WSAAsyncGetServByPort function call with a buffer large enough to receive all the desired information (that is, no smaller than the low 16 bits of lParam).

The error code and buffer length should be extracted from the lParam using the macros WSAGETASYNCERROR and WSAGETASYNCBUFLEN, defined in WINSOCK2.H as:

#define WSAGETASYNCERROR(lParam)            HIWORD(lParam)

#define WSAGETASYNCBUFLEN(lParam)           LOWORD(lParam)

The use of these macros will maximize the portability of the source code for the application.

Return Values

The return value specifies whether or not the asynchronous operation was successfully initiated. Note that it does not imply success or failure of the operation itself.

If the operation was successfully initiated, WSAAsyncGetServByPort returns a nonzero value of type HANDLE which is the asynchronous task handle for the request (not to be confused with a Windows HTASK). This value can be used in two ways. It can be used to cancel the operation using WSACancelAsyncRequest. It can also be used to match up asynchronous operations and completion messages, by examining the wParam message argument.

If the asynchronous operation could not be initiated, WSAAsyncGetServByPort returns a zero value, and a specific error number can be retrieved by calling WSAGetLastError.

Comments

The buffer supplied to this function is used by Windows Sockets to construct a servent structure together with the contents of data areas referenced by members of the same servent structure. To avoid the WSAENOBUFS error noted above, the application should provide a buffer of at least MAXGETHOSTSTRUCT bytes (as defined in WINSOCK2.H).

Error Codes

The following error codes can be set when an application window receives a message. As described above, they can be extracted from the lParam in the reply message using the WSAGETASYNCERROR macro.

The following errors can occur at the time of the function call, and indicate that the asynchronous operation could not be initiated.

See Also