WSAAsyncGetHostByAddr  5MP7MN

The Windows Sockets WSAAsyncGetHostByAddr function gets host information corresponding to an addressasynchronous version.

HANDLE WSAAsyncGetHostByAddr (

Parameters

hWnd

[in] The handle of the window which should receive a message when the asynchronous request completes.

wMsg

[in] The message to be received when the asynchronous request completes.

addr

[in] A pointer to the network address for the host. Host addresses are stored in network byte order.

len

[in] The length of the address.

type

[in] The type of the address.

buf

[out] A pointer to the data area to receive the hostentOKKRB8 data. Note that this must be larger than the size of a hostent structure. This is because the data area supplied is used by Windows Sockets to contain not only a hostent structure but any and all of the data which is referenced by members of the hostent structure. It is recommended that you supply a buffer of MAXGETHOSTSTRUCT bytes.

buflen

[in] The size of data area buf above.

Remarks

This function is an asynchronous version of gethostbyaddr, and is used to retrieve host name and address information corresponding to a network address. Windows Sockets initiates the operation and returns to the caller immediately, passing back an opaque "asynchronous task handle" which the application can use to identify the operation. When the operation is completed, the results (if any) are copied into the buffer provided by the caller and a message is sent to the application's window.

When the asynchronous operation is complete the application's window hWnd receives message wMsg. The wParam argument contains the asynchronous task handle as returned by the original function call. The high 16 bits of lParam contain any error code. The error code can be any error as defined in WINSOCK2.H. An error code of zero indicates successful completion of the asynchronous operation. On successful completion, the buffer supplied to the original function call contains a hostentOKKRB8 structure. To access the elements of this structure, the original buffer address should be cast to a hostent structure pointer and accessed as appropriate.

Note that if the error code is WSAENOBUFS, it indicates that the size of the buffer specified by buflen in the original call was too small to contain all the resultant information. In this case, the low 16 bits of lParam contain the size of buffer required to supply ALL the requisite information. If the application decides that the partial data is inadequate, it can reissue the WSAAsyncGetHostByAddr function call with a buffer large enough to receive all the desired information (that is, no smaller than the low 16 bits of lParam).

The error code and buffer length should be extracted from the lParam using the macros WSAGETASYNCERROR and WSAGETASYNCBUFLEN, defined in WINSOCK2.H as:

#define WSAGETASYNCERROR(lParam)            HIWORD(lParam)

#define WSAGETASYNCBUFLEN(lParam)           LOWORD(lParam)

The use of these macros will maximize the portability of the source code for the application.

Return Values

The return value specifies whether or not the asynchronous operation was successfully initiated. Note that it does not imply success or failure of the operation itself.

If the operation was successfully initiated, WSAAsyncGetHostByAddr returns a nonzero value of type HANDLE which is the asynchronous task handle (not to be confused with a Windows HTASK) for the request. This value can be used in two ways. It can be used to cancel the operation using WSACancelAsyncRequest. It can also be used to match up asynchronous operations and completion messages, by examining the wParam message argument.

If the asynchronous operation could not be initiated, WSAAsyncGetHostByAddr returns a zero value, and a specific error number can be retrieved by calling WSAGetLastError.

Comments

The buffer supplied to this function is used by Windows Sockets to construct a structure together with the contents of data areas referenced by members of the same hostent structure. To avoid the WSAENOBUFS error noted above, the application should provide a buffer of at least MAXGETHOSTSTRUCT bytes (as defined in WINSOCK2.H).

Error Codes

The following error codes can be set when an application window receives a message. As described above, they can be extracted from the lParam in the reply message using the WSAGETASYNCERROR macro.

The following errors can occur at the time of the function call, and indicate that the asynchronous operation could not be initiated.

See Also